UELIA Cross-linked 3D Network Solves Key Challenges —Water-Free Penetration, Zero Irritation, No Collagen Damage,Enabling Targeted Release and Smart Self-Recovery
Treatment Protocol1.Cleanse & Prepare: Cleanse face, optionally spray Renewing Balance Mist for antioxidant protection. 2.Area Protection: Apply petroleum jelly around eyes, lips, and nasal folds to shield sensitive areas. 3.Zoned Acid Application: Apply compound acid evenly in sequence—T-zone first, then cheeks—with extra attention to targeted areas. 4.Massage & Penetration: Massage for 5–8 minutes until redness appears and a white frost forms on inflamed areas (no neutralization required). 5.Residue Removal: Rinse thoroughly with water or wipe clean with a damp cotton towel. 6.Soothing & Recovery: Apply a cold compress, followed by a sodium hyaluronate repair mask or gel to calm the skin. 7.Protection & Seal: Finish with moisturizer and sunscreen.
Before You Start
1.Cleanse Your Face – Wash your face to remove excess oil and dirt.
2.Get Your Supplies Ready – Open the treatment kit. Take out the small brush, mixing bowl, and disposable gloves. Put on the gloves.
3.Prepare the Gel – Pour all of the Medical Skin Care Hydrogel into the mixing bowl and set it aside for now.
Main Steps
1.Protect Sensitive Areas – Apply a thin layer of Vaseline (or similar protective ointment) around your eyes, lips, and the sides of your nose. This creates a barrier to prevent irritation.
2.Apply the Acid Blend
oOpen the Composite Acid Antibacterial Gel.
oUse the small brush to pick up some of the gel. Apply it first to your T-zone (forehead and nose), then to your cheeks. Use your fingers to gently massage it in.
oNote: For trouble spots like blackheads or pimples, you can apply a little extra gel.
3.Apply the Hydrogel
oUse your fingers to scoop some of the Medical Skin Care Hydrogel from the bowl. Spread it over the areas where you just put the acid gel. Massage it in with a little pressure to help absorption.
4.Key Tip
oYou can repeat steps 2 and 3 a few times for better results. Aim for a total massage time of 5 to 8 minutes (longer if your skin tolerates it well). Stop when you notice slight redness and a white, frosty look on inflamed areas – that means it's working.
After the Treatment
1.Rinse Off – Wash your face thoroughly with water, or use a wet cotton cloth to gently wipe off all the product.
2.Soothe Your Skin – Take the medical repair mask from the kit and place it on your face. Leave it on for about 15 minutes to calm your skin.
3.Post-Treatment Care – After acid treatments, your skin needs extra moisture and strong sun protection. For one week, avoid saunas, long hours in direct sunlight, or anything else that might irritate your skin.
Treatment Schedule & Important Storage Info
How Often – It's recommended to do this treatment once every two weeks. A full course is 3 to 5 treatments.
Product Use – One kit contains exactly what you need for one full course. Once opened, do not save any leftover product for later – it's meant for single use to keep things sterile and effective.
UELIA Cross-linked 3D Network Solves Key Challenges —Water-Free Penetration, Zero Irritation, No Collagen Damage,Enabling Targeted Release and Smart Self-Recovery
Treatment Protocol1.Cleanse & Prepare: Cleanse face, optionally spray Renewing Balance Mist for antioxidant protection. 2.Area Protection: Apply petroleum jelly around eyes, lips, and nasal folds to shield sensitive areas. 3.Zoned Acid Application: Apply compound acid evenly in sequence—T-zone first, then cheeks—with extra attention to targeted areas. 4.Massage & Penetration: Massage for 5–8 minutes until redness appears and a white frost forms on inflamed areas (no neutralization required). 5.Residue Removal: Rinse thoroughly with water or wipe clean with a damp cotton towel. 6.Soothing & Recovery: Apply a cold compress, followed by a sodium hyaluronate repair mask or gel to calm the skin. 7.Protection & Seal: Finish with moisturizer and sunscreen.